No. We can work with both large and small areas – Contact us for a free consultation on your site

No. It doesn’t have to be, although it would the best to apply at first to save all the hassles. We can always propose a way to upgrade flooring at any stage – Contact us for a free consultation on your site

We understand that for upgrading and repair works, time is the utmost critical factor. One of the most important traits of Forintech products is fast-drying which would save a considerable amount of time and minimize the impact to the live production. For detailed case by case consultation, please contact technical team for a more thorough inspection.

Yes. we have dedicated products catering to wet manufacturing condition. Forincrete MF is usually a good choice and Forincrete AS can be applied to those places with an even higher anti-slippery requirement. The amount of slip resistance required will depend on the operating conditions of the environment in question and can be adjusted by using different sizes and/or shapes of aggregate to produce the desired texture. It is important to note that slip resistance and cleanability are inversely proportional to one another so it is important to strike a good balance Clients don’t have worry about issues like slippery floorings and water seeping through the flooring etc. More insights can be shared after on-site inspection.

Yes. It would be the best if machineries can be moved but we are able to apply on the area surrounding the machine as well.

Yes. After inspection, we can also do repair work to the affected area and propose catered recommendation to flooring maintenance. However, please note that there will likely be colour difference at the patching area

Yes. We have dedicated material for heavy duty scenarios. Generally we would recommend Forincrete UD – please refer to our past case studies here.

Yes. Our product can resist constant cleaning and relatively high temperature. Generally, Forincrete MF will be a good choice

Our dedicated anti-slippery product can perfectly solve this issue, and it is especially beneficial in the wet processing areas.

We understand F&B industry would have a more stringent requirement on factory environment. Whilst the issue of tainting may not be a factor for new build projects, it does become important during renovation/refurbishment work. Forintech product is virtually odourless. Therefore, tainting of food is not an issue during the flooring installation.

Forincrete PU product line is extremely suitable for food and beverage facilities which are usually exposed to organic waste and potentially erosion from salty ingredients or even chemicals like acids etc. Forincrete product is HACCP certified and is proven in the F&B industry with numerous success cases Major benefits include:

i) Excellent Chemical Resistant

ii) Temperature resistance

iii) Low odour installation

Yes, a resin floor finish can be applied to a metal surface. The metal surface must be prepared by mechanical means to remove any rust scales, loose particles or existing paint.

Our product ranges from 2mm to more than 10mm in thickness. Typically, we recommend a 2-4mm thickness in flooring which is suitable for most of the industrial scenarios, but we can also do customization if a thicker flooring is necessary.

Normally customer doesn’t have to much and we will do a site inspection beforehand to determine the quality of the flooring basics and to see if any further steps needs to be taken. Please consult with our technical team for more information. Contact us

All material is supplied in pre-weighed packs to ensure optimum performance. Therefore, it is not necessary to split or proportion packs on site. The pre-weighed resin is then mixed on site by a high-speed drill or portable mixer before being applied to the prepared substrate. The exact application process and required tools will vary depending on the type of flooring being installed. The application process may involve the use of a hand or power trowel, spreading the material with a pin rake or notched squeegee, the use of nap or spiked rollers, etc. All of Forintech approved applicators have been fully trained in the application processes for the various flooring systems offered by Forintech. If you would like to know more about the application process of one of our flooring systems please contact our technical department for further details. Contact us

Resin floor finishes can be installed onto a wide range of substrates including concrete, cementitious underlays, marine grade plywood and metal as well as various types of tiles and pre-existing resin floor finishes. Prior to the application of a resin floor finish, the substrate must be determined to be structurally sound and free from dust, oil, grease and other surface contaminants. Tiles and pre-existing resin floor finishes must be well bonded to the original substrate.

We can install a resin floor in almost any colour. We have a range of standard colours available for each of the products that we supply. Depends on the size of the order, if the colour you would like is not available as standard we can have a colour specially blended to match as close as practicable any colour sample that you provide. Non-standard and specially blended colours are more expensive than standard colours, but create a more individual floor

Surfaces are installed by well-trained personnel authorised by Forintech, who have been trained and are experience with our products. This guarantees a high level of quality and ensures selection of a preferred functional and aesthetic solution can be made with complete confidence.